SOLID 810 is a two-component, transparent water insulation material that can be easily applied to various surfaces such as ceramics, marble, granite, tiles, natural stone, concrete, and is resistant to UV rays and chemical and physical effects.
PRODUCT DESCRIPTION
SOLID 810, It is a two-component, transparent water insulation material that can be easily applied to various surfaces such as water insulation, ceramic, marble, granite, tile, natural stone,concrete, resistant to UV rays, chemical and physical effects. It can be used for water insulation and decorative purposes. It forms a transparent, elastic and seamless layer after drying.
ENVIRONMENTAL CONDITIONS
The ambient temperature should be between +15°C and 35°C. Application should not be done when the relative humidity exceeds 80%. In order to prevent surface condensation, the surface temperature should be at least 3-5 °C above the dew point.
It should be known that consumption will increase in applications to be made at low temperatures. The surface temperature should be at least +5°C and at most 45°C.
APPLICATION FEATURES
•It provides waterproof properties and an aesthetic coating.
•It can be applied directly without requiring a primer.
•It is resistant to UV rays and is not affected by external factors.
•It easily solves insulation problems on floors without damaging the existing coating.
•It creates a transparent insulation layer.
•It has high adhesion capacity on a glossy surface.
PACKAGING
20 KG. ve 5 KG. 20 It is produced in packages.
One Bucket SOLID 810 A Componenti net 10,50kg.
One gallon SOLID 810 B Hardener Component B net 4,50 kg.
Bir kova SOLID 810 A Komponenti net 3,50 kg’dır.
One gallon SOLID 810 B Hardener Component B net 1,50 kg.
SHELF LIFE
The material should be stored in its original packaging in a cool and dry place. The storage life of the material in unopened packaging is 12 months for component A and B.
HEALTH AND SAFETY INFORMATION
Read the MSDS form (Material Safety Data Sheet) for necessary safety rules and warnings. The minimum safety rules to be followed are as follows.
-Contact of the product with skin and eyes should be prevented by using gloves, protective glasses, face mask andindustrial cream.
-Ensure adequate air circulation during application and until the paint dries.
-If the product comes into contact with the skin, it should be washed with warm water and soap or industrial cleaner.If splashed into eyes, rinse with water for at least 10 minutes and seek medical attention.
-All warning notes on the buckets should be read carefully and recommended working rules should be
*Our information on products is normally based on our own laboratory experiments and research. Our company is not responsible for any work under inappropriate application conditions. The right to change this information is reserved by our company. For more detailed information, please apply.
SOLID 810 2K TRANSPARENT WATER INSULATION PRODUCT
It is used for water sealing on tile surfaces such as terraces, balconies, bathrooms, kitchens, and in outdoor areas such as roofs, facades and pools. UYGULAMA: The surfaces to be applied must be completely free of residues such as oil, dirt, dust and rust, clean and dry. In order to ensure good adhesion to the surface, cleaning must be done meticulously. Then, all of the B component must be added to the A component and mixed thoroughly in the specified proportions. The life of the mixture is approximately 25 minutes. The prepared mixture can be applied with a brush, roller or spray gun.
| TECHNICAL PROPERTIES | |
|---|---|
| Appearance | Fully glossy |
| Color | Transparent |
| Density (g/ml 20°C) | 1.06 ± 0.05 |
| Mixing Ratio (by weight) | Component A: 70 parts Component B: 30 parts |
| Solid Content by Weight (w/w) | 98% ± 2 |
| Application Method | Trowel and smoothing |
| Pot Life (20ºC) | 20–25 minutes |
| Full Cure (days/20°C) | 4–10 days |
| Flexural Strength (7 Days) | 28 N/mm² (TS EN 196-1) |
| Compressive Strength (7 Days) | 71 N/mm² (TS EN 196-1) |
| Shore D Hardness (7 Days) | 78 |
| Continuous Thermal Resistance | +50°C, max 7 days: +80°C |
*DRYING INFORMATION (100 micron DFT)
| Touch Dry | Hard Dry | Minimum Recoat Time | |
|---|---|---|---|
| -5°C | 12 hours | 29–30 hours | 24 hours |
| 0°C | 9 hours | 20–21 hours | 18 hours |
| 5°C | 6 hours | 13–14 hours | 12 hours |
| 15°C | 120–160 minutes | 5–6 hours | 3.5 hours |
| 25°C | 80–100 minutes | 3–4 hours | 2 hours |
| 35°C | 60–80 minutes | 1.5–2 hours | 1.5 hours |
NOTE: As the application thickness increases, drying time also increases.
| CONSUMPTION | ||
|---|---|---|
| Wet Film Thickness (μ) | Dry Film Thickness (μ) | Theoretical Consumption ± 10 (kg/m²) |
| 188 | 169 | 0.200 |
NOTE: As the application thickness increases, consumption also increases.
Surface Preparation
The application surface is carefully cleaned of dirt, oil and grease. Loose old concrete pieces are cleaned from the surfaces. Rust and burrs on the surface are cleaned using a diamond-tipped machine according to SA 2 ½ standards.
Use of the Product
SOLID 810 components are thoroughly mixed separately before use. Then a homogenous mixture is made with its own hardener. To prevent condensation, it is applied only on a dry and clean surface with a temperature above the dew point. The binder temperature should be 20-35°C. Thinning may be required with very long spray hoses and paint temperatures lower than 15°C. This may lead to lower film thickness and longer drying time.
Application method; depending on the type of stone, the amount required is determined by the applying dealer.
Fill out the form to request pricing, application or technical information about this product.
Solid Epoxy Flooring Systems provides durable epoxy flooring products and coating solutions for garages, commercial spaces and industrial facilities.
Strong surfaces. Clean finishes. Long-lasting protection.
We will get back to you as soon as possible.